|
|
| WarP-Drive Hall-Effect Pedal Assembly |
|
The WarP-Drive Hall-effect pedal assembly (HEPA) is an automotive accelerator pedal assembly with dual Hall-effect sensors. It includes dual return springs and has convenient mounting points. The Hall-effect unit eliminates the annoying wear out of regular pot boxes. The pedal will require a custom bracket for mounting and may not fit all cars. In those circumstances, consider the WarP-Drive Cable-Pull throttle unit listed below.
Price includes a 10' section of shielded cable which comes with waterproof connectors installed on both ends of the cable - one for the Hall-effect unit, and the other for the WarP-Drive controller. This provides a factory installation appearance.
The functions of each wire are the following:
-
Orange: 0.8V to 4.45V, signal 1
- Blue: ground for signal 1
- White: 5V supply for signal 1
- Green: 1.6V to 4.95V, signal 2
- Black: ground for signal 2
- Red: 5V supply for signal 2
- Drain wire: grounded
|
|
#201-HEPA-L
|
|
| WarP-Drive Hall-Effect Cable-Pull Throttle |
Installation Guide  |
The WarP-Drive Hall-effect cable-pull throttle assembly is a patent-pending, custom product by NetGain Controls. It is is an automotive-quality throttle input device with dual Hall-effect sensors and a variety of features to make it reliable and easy to install. It includes dual return springs. It also comes with an additional spring to allow for customization of the return tension by replacing the heavier spring with a lighter one.
The Hall-effect unit eliminates the annoying wear out of regular pot boxes. The device easily accommodates various installations, where different throttle cable travel distances are required for each vehicle. This is accomplished with a set of 5 inner discs, giving the following travel options: 1.125", 1.25", 1.5", 1.75", and 2". The stock throttle cable is inserted between the top and bottom discs by removing the top disc, selecting the appropriate inner disc corresponding to the right travel distance, replacing the top disc and securing it, then reattaching the springs.
Price includes a 5' section of shielded cable which comes with waterproof connectors installed on both ends of the cable - one for the Hall-effect unit, and the other for the WarP-Drive controller. This provides a factory installation appearance.
|
|
#201-WDT-CP
|
|
| Soliton1 Hall-Effect Throttle Assembly |
|
The Soliton1 Hall-effect throttle assembly is a custom part provided exclusively by EV Source for the Soliton1 controller. It is an automotive accelerator assembly. It includes dual return springs and has convenient mounting points. The Hall-effect unit eliminates the annoying wear out of regular pot boxes. Throttle response is very smooth and the feel of the pedal is very natural.
Price includes a 10' section of shielded cable (including drain wire), which comes with the matching connector for the pedal side and bare wire ends for the controller side. The connections to the Soliton1 are as follows:
- Red wire: "SIGNAL +5V"
- Black wire and drain wire (bare wire): "SIGNAL GND"
- White wire: "THROTTLE"
After connecting, run through the throttle calibration provided in the browser interface.
|
|
#200-SOL1-HEPA
|
|
| Evnetics Throttle Pot Box Assembly |
|
Evnetics has produced this top-notch throttle unit to work seamlessly with the Soliton1 controller and a cable-driven throttle. It has an automotive-quality sensor that is designed to be mounted in harsh environments such as under the hood.
The throttle unit comes with a cable that easily connects to the Soliton1 controller. It has an arm with multiple adjustment points to satisfy the widely varying throttle cable requirements of various automobiles. Construction is of polished aluminum. The throttle arm rotates on dual bearings for smooth action.
Note: A single return spring is provided. It is important that an additional return spring is added to the installation to provide redundancy in case the primary spring breaks.
|
|
#201-SOL1-POT |
|
| Curtis PB-6 Potbox Assembly |
 |
This is a standard 0-5kohm with microswitch. Recommended for use with Curtis and Alltrax controllers.
Note: A single return spring is provided. It is important that an additional return spring is added to the installation to provide redundancy in case the primary spring breaks.
|
|
#201-PB6
|