|
|
Dual Motor Adapter/Coupler |
|
This custom adapter has everything you need to connect dual WarP 9's or WarP 11 (the picture shows a WarP 9 with a WarP 11 only to show it will connect to either motor - this configuration would not be recommended). The adapter will keep the motors perfectly aligned to prevent vibration and subsequent wear on the motors and coupler.
The "Street" version is intended for operation under 4000 RPM, with continuous at 2500 RPM or less. It uses a keyed shaft coupler that will work with stock motors. The "Race" version is for the most demanding applications where RPMs are higher and torque greater and requires custom NetGain motors with a splined shaft.
|
Street
#300-WP-WP
|
Race
#300-WP-WP-R
|
|
|
|
Dana 1310 End yoke for 1.125in. Shaft, .250in. Keyway |
|
|
This 1310 end yoke fits on the drive shaft of all WarP motors, including the ImPulse 9. It is useful for direct coupling the motors to a driveshaft, or to facilitate coupling two motors together where angular alignment cannot be guaranteed.
|
|
#301-2-4-503
Stock: 2
|
|
Dana U-Joint Kits |
|
A U-Joint is the coupler between two yokes. The style of the U-Joint must match the yoke. To connect a 1350 yoke to another 1350 yoke, use a 1350 U-Joint kit. The 1310 to 1350 conversion U-Joint is used where one yoke is a 1310 and the other is a 1350. The 1310 model is shown in the picture. The other models will look similar. |
1310
#301-5-785X
Stock: 1
|
1350
#301-5-799X
| 1310 to 1350
#301-5-460X
|
|
|
Dana 1310 Yokeshaft, 1.375-16 x 2.50in Spline |
|
The yoke shaft can be used in conjunction with a slip yoke assembly to provide a telescoping driveline connection. An example where this would be needed is when coupling motor fixed to the chassis to a differential that is moving up and down. The length of the driveshaft connection will be changing in this situation.
When coupled with part number 301-3-3-2591KX below, the total length of the assembly is about 12.5" fully extended. Fully compressed, total length is about 10.75" with total travel about 1.75".
The yoke is a 1310. The picture shows the yoke shaft coupled to a slip yoke, and the U-Joint installed. The item price includes only the yoke shaft. Other accessories are sold separately on this page.
|
|
#301-2-82-58X
|
|
Dana 1350 Slipyoke, 1.375-16 Spline, 6.625in Length |
|
The slip yoke can be used in conjunction with a yoke shaft to provide a telescoping driveline connection. An example where this would be needed is when coupling motor fixed to the chassis to a differential that is moving up and down. The length of the driveshaft connection will be changing in this situation.
When coupled with part number 301-2-82-58X above, the total length of the assembly is about 12.5" fully extended. Fully compressed, total length is about 10.75" with total travel about 1.75".
The yoke is a 1350. The picture shows the slip yoke coupled to a yoke shaft, and the U-Joint installed. The item price includes only the slip yoke. Other accessories are sold separately on this page.
|
|
#301-3-3-2591KX
|
|
3/8 in. Set Screw, .750 in. Length, Square Head w/ Hole |
|
This is a 3/8-16 set screw. It's advantage over a standard style set screw is the ability to apply greater torque when setting it, and the ability to use a lock wire to ensure the set screw doesn't vibrate loose.
Compatible with the 1310 end yoke on this page.
|
|
#300-SS-375-16-750-SQ-H
Stock: 1
|
|
1/4in. Plain Steel Square Key, 1-1/2 in. Length, Undersized |
|
.250" square key stock with smoothed ends. It is slightly undersized making it easy to install. Length is 1 1/2 inches.
|
|
#301-98870A230
Stock: 10
|